Check It Out

 

 

The article below in relation to How to Install a Bathtub Yourself is pretty much fascinating. Don't overlook it.

Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is readily accessible, the task can move easily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about using one before you start. Possibilities are you might need an expert plumber to make tube connections.
This article will certainly help you set up a brand-new bathtub in your washroom if you have currently bought a new bathtub and do not require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic because of the limited access that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in location between the tap and the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Installing the Bath tub

Making use of the two wooden boards under its feet, position the bath tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub should wait up until the bathtub has actually been made use of a minimum of when as this will resolve it into its last position.

 

 

Planning for the Installation

Firstly, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last placement.

 

 

Tiling Around the Bathtub

In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can crack fairly very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly offered on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a serious person who reads on Installing A Bathtub, I imagined sharing that excerpt was really useful. Don't hesitate to take the opportunity to distribute this article if you enjoyed it. I truly appreciate reading our article about Tools You Need to Install a New Bathtub .

Click On This Link